Journal of International Society of Preventive and Community Dentistry

ORIGINAL ARTICLE
Year
: 2016  |  Volume : 6  |  Issue : 2  |  Page : 161--166

Comparative evaluation of different mechanical modifications of denture teeth on bond strength between high-impact acrylic resin and denture teeth: An in vitro study


Sumit Singh Phukela1, Siddesh Kumar Chintalapudi2, Harleen Sachdeva3, Rupinder Singh Dhall4, Neeraj Sharma5, Allama Prabhu6 
1 Department of Prosthodontics, Shree Guru Gobind Singh Tricentenary (SGT) Unversity, Gurgaon, Haryana, India
2 Department of Prosthodontics, Shree Sai Dental College and Research Institute, Srikakulam, Andhra Pradesh, India
3 Department of Prosthodontics, RKDF Dental College and Research Centre, Bhopal, India
4 Department of Prosthodontics, Himachal Institute of Dental Sciences, Paonta Sahib, Himachal Pradesh, India
5 Department of Prosthodontics, Modern Dental College and Research Centre, Indore, Madhya Pradesh, India
6 Department of Public Health Dentistry, College of Dental Sciences, Davangere, Karnataka, India

Correspondence Address:
Dr. Sumit Singh Phukela
Department of Prosthodontics, Faculty of Dental Science, SGT University, Gurgaon, New Delhi - 110 010
India

Aim and Objective: Acrylic teeth separates from the denture base and remains a major worry in day-to-day routine dental procedure. The present study was conducted to comparatively evaluate different mechanical modifications of acrylic teeth on bond strength between Lucitone 199 heat cure resin and cross-linked teeth. Materials and Methods: The test specimens, central incisors (21) were demarcated into four groups. Group 1 was the control group, whereas Group 2, Group 3, and Group 4 were experimental groups modified with round groove, vertical groove, and T-shaped groove, respectively. The preparation of masterpiece was done by aligning the long axis of the central incisor teeth at 45° to the base of a wax block (8 mm × 10 mm × 30 mm), with ridge lap surface contacting the base. These test specimen (21) was prepared by Lucitone 199 heat cure resin. Evaluation of bond strength of all the specimens was done using universal tester (materials testing machine). Shapiro–Wilk Test, one-way analysis of variance (ANOVA), and Bonferroni test were done to do statistical investigation. Results: Group 1 specimens prepared by Lucitone 199 heat cure resin showed the lowest bond strength and Group 4 specimens prepared with T-shaped groove packed with Lucitone 199 exhibited the highest bond strength. Conclusion: The bond strength between Lucitone 199 heat cure resin and cross-linked teeth was increased when mechanical modifications was done on denture teeth. The specimens prepared with T-shaped groove packed with Lucitone 199 heat cure resin showed the highest bond strength followed by Group 3, Group 2, and lastly Group 1 prepared by Lucitone 199 heat cure resin.


How to cite this article:
Phukela SS, Chintalapudi SK, Sachdeva H, Dhall RS, Sharma N, Prabhu A. Comparative evaluation of different mechanical modifications of denture teeth on bond strength between high-impact acrylic resin and denture teeth: An in vitro study.J Int Soc Prevent Communit Dent 2016;6:161-166


How to cite this URL:
Phukela SS, Chintalapudi SK, Sachdeva H, Dhall RS, Sharma N, Prabhu A. Comparative evaluation of different mechanical modifications of denture teeth on bond strength between high-impact acrylic resin and denture teeth: An in vitro study. J Int Soc Prevent Communit Dent [serial online] 2016 [cited 2022 Jan 29 ];6:161-166
Available from: https://www.jispcd.org/article.asp?issn=2231-0762;year=2016;volume=6;issue=2;spage=161;epage=166;aulast=Phukela;type=0